Announcement

Collapse
No announcement yet.

Snow Wheeling Jan 15th

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Re: Snow Wheeling Jan 15th

    Originally posted by 71BRONCO71 View Post
    Everything went well with the truck. My ARB did have a problem but thats because I ripped the line out when I ran over a metal pole. I didnt see it but I did hear it. I found it and bent it back up like nothing happened. (you couldnt even tell.)
    On a side note:
    I found out that my motor goes to 4 grand
    Hey Ryan, I think if you were at 4grand you would not have gottin suck?
    My two boys have been speaking in high RPM noises all weekend. I'm a proud bronco owner and dad!
    Leave No One Behind
    KK6AUW

    Comment


    • Re: Snow Wheeling Jan 15th

      Originally posted by ProudPapa View Post
      Hey Ryan, I think if you were at 4grand you would not have gottin suck?
      Im still sticking to my story. Its Galens fault

      x2 haha
      {o===o}
      Originally posted by TBS-POPS
      EXCUSSSSSSE ME oh RUBIMASTER!!! I forgot how Awesome YOU ARE!!! I BEG your forgivness....
      Originally posted by CityHick
      I don't give probabilities in percentage format anymore

      Comment


      • Re: Snow Wheeling Jan 15th

        Originally posted by 71BRONCO71 View Post
        ...because I ripped the line out when I ran over a metal pole..
        Did you rip the line out of the compression fitting or what? I took one look at those plastic air lines and threw them in the garbage (or donated them to someone in need, don't remember). I replaced them with braided stainless lines complete with AN style fittings. Have not had a single problem yet... however I don't usually run over metal poles either
        1970 Bronco
        My build thread

        Comment


        • Re: Snow Wheeling Jan 15th

          Originally posted by CityHick View Post
          Did you rip the line out of the compression fitting or what? I took one look at those plastic air lines and threw them in the garbage (or donated them to someone in need, don't remember). I replaced them with braided stainless lines complete with AN style fittings. Have not had a single problem yet... however I don't usually run over metal poles either
          It tore right out fitting. If it was a braided line, Im sure it would have ripped out the entire brass fitting out of the third member.
          {o===o}
          Originally posted by TBS-POPS
          EXCUSSSSSSE ME oh RUBIMASTER!!! I forgot how Awesome YOU ARE!!! I BEG your forgivness....
          Originally posted by CityHick
          I don't give probabilities in percentage format anymore

          Comment


          • Re: Snow Wheeling Jan 15th

            Originally posted by 71BRONCO71 View Post
            It tore right out fitting. If it was a braided line, Im sure it would have ripped out the entire brass fitting out of the third member.
            You're probably right on that!
            1970 Bronco
            My build thread

            Comment


            • Re: Snow Wheeling Jan 15th

              Originally posted by BroncoLady
              Second try:
              Looks like a great time.. Now I am motivated to get my Junk rolling again! That toy looks familiar... Just like the one down the street from me and Dave...
              '88 347 roller, Exploder EFI, WH Shorties, NP435, twin stick D-20 with Tera lows, 44 4:56's w/ARB chromos and CTMs, 9" Detroit, cust dash, wiring and STILL ALMOST "DONE"!...

              Comment


              • Re: Snow Wheeling Jan 15th

                it is that one. I am a bad influance on him... ;-)
                WT 4x4
                91' One Ton Bronco
                1971 Bronco
                9/11/01 Never Forget

                Comment

                Working...
                X